Serial Wireless WIFI Module (ESP8266 )

ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.

ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

Features

SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated /baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Solutions

Supports APSD for optimal VoIP applications
Patented spurious noise cancellation algorithm for integration in SOC applications
Supports Bluetooth co-existence interface
Self-calibrated RF to ensure optimal performance under all operating conditions
Zero factory tuning
No external RF components

802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
AT Command Set

Warnings:
This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect RX or TX on 5V FOR Arduino will
destroy this module. You must use a logic level converter, or a 3.3V FOR Arduino

The 3.3V supply FOR Arduino Uno has inadequate current capabilit to power this module. You must provide a separate,
higher 3.3V supply(about 300mA or better)

  • N/A

More from this Category

H201 RF Receiver Module with RF Transmitter Module (433MHZ)

H201 RF Receiver Module with RF Transmitter Module (433MHZ)

R 44.80 View
Out of Stock
NEO-6M GPS Module

NEO-6M GPS Module

R 207.20 View
Infrared (IR) Wireless Remote Control Module HX1838

Infrared (IR) Wireless Remote Control Module HX1838

R 28.00 View
2.4GHz Wireless Transceiver Module (NRF24L01, onboard antenna)

2.4GHz Wireless Transceiver Module (NRF24L01, onboard antenna)

R 39.20 View
UART 125Khz EM4100 RFID Key Card Module (RDM6300)

UART 125Khz EM4100 RFID Key Card Module (RDM6300)

R 128.80 View
Out of Stock
CC1101 RF1101 Wireless Transceiver Module with SMA Antenna

CC1101 RF1101 Wireless Transceiver Module with SMA Antenna

R 324.80 View
433Mhz Superheterodyne Wireless Receiver Module (315M RXB6)

433Mhz Superheterodyne Wireless Receiver Module (315M RXB6)

R 112.00 View
Out of Stock
GPRS with GSM and GPS Shield A7 (SMS, Voice Calls & GPS Location)

GPRS with GSM and GPS Shield A7 (SMS, Voice Calls & GPS Location)

R 476.00 View
125KHz RFID Reader Module (5V, UART 3Pin, EM4100)

125KHz RFID Reader Module (5V, UART 3Pin, EM4100)

R 128.80 View
FM Stereo Radio Module RDA5807M Wireless Module

FM Stereo Radio Module RDA5807M Wireless Module

R 16.80 View