ICL8038 Function Signal Generator DIY Kit - South Africa Arduino, Robotics & Electronics Supplier South Africa: R99.00
Leobot Electronics South Africa (Pretoria)
ONLINE SHOP (based in Pretoria)
Nation-wide delivery or, collect from our premises in Waverley, Pretoria
- Next batch of new stock coming early February 2023!

Leobot Electronics South Africa - Low Cost Arduino & Electronic Component Supplier based in Waverley, Pretoria, South Africa.

    • Leobot Electronics Online Shop

ICL8038 Function Signal Generator DIY Kit
    Home / Kits / ICL8038 Function Signal Generator DIY Kit
  • ICL8038 Function Signal Generator DIY Kit

#2787: ICL8038 Function Signal Generator DIY Kit

R99.00


The ICL8038 is a precision oscillating integrated circuit with multiple waveform outputs. The frequency and duty cycle of the output waveform can also be controlled by current or resistance. Since the chip has an FM signal input, it can be used to frequency-modulate low-frequency signals. The kit is designed for the frequency range commonly used, divided into five stalls adjustable, can produce from 10Hz-450KHz low distortion sine wave, triangular wave, square wave pulse signal.

Components parameters according to the original given values given in the selection, the circuit of integrated circuits, diodes, transistors, electrolytic capacitors are polar components, careful not to install the opposite direction.
All components should be mounted on the circuit board surface.
Each potentiometer has an influence on each other, please select the appropriate frequency band (J2 short-circuit cap) repeatedly carefully adjusted, the frequency is lower than 50Hz and higher than 200KHz is not recommended.
Circuit power supply: 12-24V

 

Product Details

ICL8038 pin function:
1 pin, 12 pin: sine wave adjustment side
2 pin: sine wave output
3 pin: triangular wave output
4 pin, 5 pin: frequency and duty cycle (or waveform asymmetry) adjustment
6 pin: V +, positive power supply
7 pin: frequency offset
8 pin: frequency adjustment input
9 pin: square wave output. This is an open collector output. When working, connect a load resistor from the pin to the corresponding positive supply, to obtain a TTL-compatible square wave output, the load resistor must be connected to the + 5V supply.
10 pin: timing capacitor side
11 pin: V-, negative power supply terminal connect ground. When using positive and negative power supply, 11 pin connected to the negative power supply, the output waveform is relative to 0V symmetry. When using a single positive power supply, pin 11 is grounded and the output waveform is unipolar and the uniform voltage is + VCC / 2.
13 pin, 14 pin: empty pin
The frequency range is 10KHz-450KHz, divided into 5 bands, with switch J2 (short-circuit cap) to switch, PR1 is the frequency adjustment, RP2 is the square wave duty cycle adjustment, RP3 is the square wave linear adjustment, RP4 is the sine wave distortion adjustment, RP5 is the output amplitude adjustment.
The circuit can be powered from a single 12-24V supply from J1. J4 is the waveform output, 1 pin output with DC bias signal, 2 pin output pure signal, the output waveform category can be switch by J3 (short-circuit cap).


Product Details

Est. Packaging Size Specifications

N/A

Other Products in the same category

BUY

ICL8038 Function Signal Generator DIY Kit

Regular price: R99.00
Qty To Purchase:
In Stock: 9



GET NOTIFIED!

Get notified when new stock arrives! Simply provide your email address:


Email Address:



Categories
 
  • Shipping Costs South Africa Arduino, Robotics & Electronics Supplier

Facebook

Shipping & Coverage

For South Africa, PostNet is used for shipping at R99 per order if delivered to your local PostNet or R105 if the parcel needs to be delivered to your doorstep via Aramax! Postage is FREE for orders over R1000!


We supply Arduino, Robotics and all of our other DIY Electronics throughout South Africa including Durban, Johannesburg, Pretoria, Cape Town, Bloemfontein and rural areas.


3D Printing Service available at Leobot3d.com for all your custom printing needs.


For industrial-level laser CNC machines have a look at our trusted partner www.PloughLaserMachine.com.


You can find great electronic kits in Pretoria at www.ElectroKits.co.za.


Information


Contact us

Admin Office:
1348B Breyer Avenue (Collections),

Waverley,,

Pretoria,

Gauteng,

South Africa,

Phone: 082 776 7668

Fax: 0865188874

Email:info[a.t]leobot[d.o.t]net


© 2023 Design by Leobot Electronics and w3layouts