Leobot Electronics South Africa - Low Cost Arduino & Electronic Component Supplier based in Waverley, Pretoria, South Africa.
Leobot Electronics Online Shop
R109.65
A DC-DC 10-32V to 12-35V 150W step-up booster is a type of power converter that is designed to increase the voltage of a DC power source. It operates by taking in a low voltage DC input and producing a higher voltage DC output. The input voltage range of the booster is typically 10-32V, and the output range is 12-35V. It is rated for a maximum power output of 150W. The booster is often used to power electronic devices that require a higher voltage than the input source can provide, or to provide a voltage boost to a system to increase its power capabilities. It is important to ensure that the output voltage of the booster is compatible with the voltage requirements of the device being powered.
DIY an adjustable on-board power supply, you just input DC 12V, then you can get output DC 12V-35V (adjustable), But the output voltage can not below the input voltage.DIY a booster charger.Provide power for your electronic equipment.Use Solar battery charging for electric accumulator.
nput voltage: DC 10V-32V.Output voltage: DC12V-35V(adjustable).Output current: 10A (MAX).Input current: 16A (MAX) (more than 10A please strengthen heatsink).Output power: natural cooling 100W (MAX), strengthening cooling 150W (MAX) real power.Conversion efficiency: 94% (when Output 19V 2.5A Input 16V, Reference).Output ripple: 2% (MAX).Working temperature: industrial (- 40 ° c to +85 °c) ( environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling).Full-Load temperature: 45 degrees.No-load current: 25mA typical.Voltage regulation: ± 0.5%.Load regulation: ± 0.5%.Dynamic response speed: 200uS 5%.Short circuit protection: No (Please installs the fuse or protection circuit at input parts).Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.).Dimension: 65mm x 35mm x 23.5mm.
N/A
Arduino Automated Plant Water ProjectA simple but practical Arduino project to automatically water your plants, showing the usage of a 7-Segment Display, a Soild Moisture Sensor, a Temperature Sensor and a Relay.
Arduino IntroductionIntroducing you to the awesome Arduino!
Simple Arduino RC Car/Robot A guide to construct your own Arduino-based 2 Wheel-Drive Robot
Arduino F.A.Q Arduino Frequently Asked Questions & Answers
1000W ZVS Low Voltage Induction Heater (12V-36V, 24V Recommended)
R789.95
20KV High Voltage Generator ( DC 3.6-6V, 1.5A, Pulse Arc Igniter, Step Up Boost Module Coil Transformer)
R89.80
15KV High Voltage Generator (Arc Ignition Inverter, Step Up Boost Coil)
R43.25
LM2596 Voltage Regulator Module (Buck Adjustable Step Down, Vin 3.5V - 40V, Vout 1.5V - 35V)
R38.49
DC-DC Buck Converter Step Down Module (300W,10V-40V, 20A Constant Current )
R270.40
MT3608 DC-DC Boost Module 2A (Step Up Power Supply)
R29.95
LM1117/AMS1117 3.3V DC-DC Step down Power Supply Module (4.5-7 VIn, 3.3 VOut)
R11.73
100W DC-DC Booster Step up Module (1 3-35V to 3.5~35V LTC187, With LED Voltmeter)
R163.09
AC-DC 5V 800mA 110V/220V to DC 5V Power Supply Module (Buck Converter Step Down Board Transformer)
R71.33
DC to DC 250W Constant Current Boost Step Up Module Power Supply (8.5-48V Input 10-50V Output)
R150.80
DC-DC 10-32V To 12-35V 150W Step Up Booster
CH340 USB to ESP8266 Wifi Module Adapter
R69.00
5V USB -Output Charger (Step Up Power Module)
R39.61
200W DC-DC Buck Step Up Boost Converter (7A, In 6-35V, Out 6-55V)
R193.00
AC 2000W Controller - Module
R129.95
Get notified when new stock arrives! Simply provide your email address: